Equipment guide · finishing

Commercial ironer: flatwork and rotary ironers for sheets and table linen

A commercial ironer presses and dries flat linen in one pass: a damp sheet, duvet cover or tablecloth goes in at the front and comes out smooth and dry. Choosing one comes down to your widest item, how much you finish a day, how damp the linen arrives, the energy you have, and safe guarding of a hot, turning roll.

  • Rotary vs flatwork ironers, explained plainly
  • What to measure before you ask for quotes
  • PUWER guarding rules quoted from the regulations
  • ICO registered ZA810991
  • UK company 11135452
  • Rules checked 19 November 2026
Free quotes

Get quotes for a commercial ironer

Free, no obligation. Three quick steps.

Your laundry
Options
Your details

ICO registered ZA810991 No obligation For businesses

Commercial ironer: key points
  • Ironers are for flat items: sheets, duvet covers, pillowcases, tablecloths and napkins. Shirts and tunics need a press instead.
  • Roll width sets the widest item you can feed. Measure your widest item flat and decide whether you'll feed it full width or folded.
  • An ironer dries as it presses, so roll diameter, heat and the moisture in the linen on arrival decide how fast it can run.
  • Gas-heated ironers need gas work by a Gas Safe registered engineer or competent person, depending on the premises (HSE).
  • The in-running nip between roll and bed is a dangerous part: PUWER regulation 11 requires effective guarding that can't easily be bypassed.

What types of commercial ironer are there?

Short answer

A rotary (roller) ironer has a padded roll turning against a heated bed and suits smaller volumes. A flatwork ironer carries linen round a large heated cylinder, often with a feeder and folder, and suits long runs. Presses are for shaped garments.

Rotary or roller ironer

Compact and hand-fed, often by one person. Many return the linen to the front, so the operator feeds and receives on the same side.

Flatwork ironer

One or more heated cylinders with belts or a padded bed. Larger and faster, built for sheets and covers in volume.

Feeders and folders

Add-ons that spread, fold and stack items. They take space and change how many people the line needs.

Presses

Shape collars, cuffs and tunics: a different job, worth a separate conversation if you finish uniforms.

Suppliers use 'rotary' and 'flatwork' loosely. Compare roll width, roll diameter and heating, not the label.

What can you put through a commercial ironer?

Short answer

Flat items: sheets, duvet covers, pillowcases, tablecloths, runners and napkins. Towels are tumble dried and folded instead, and shaped clothing needs a press.

General guide; follow care labels and the ironer maker's instructions
ItemIroner?Watch for
Sheets and duvet coversYesWidth against the roll; buttons and poppers can mark the padding
Tablecloths and runnersYesOften your widest items: measure them first
Pillowcases and napkinsYesMany small items, so hand feeding limits output
Towels and robesUsually notPressing flattens the pile
Shirts, tunics, chef jacketsNoNeed garment finishing

What should you measure before choosing an ironer?

Short answer

Your widest item laid flat, how many of each item you finish a day, the hours the ironer will run, how damp linen is when it arrives, your energy supply, and the working space around the machine.

Worked example (ASSUMED figures). ASSUMED widest item: a tablecloth 2.4 m wide. Fed full width, the roll must exceed 2.4 m plus the maker's margin. Folded lengthways it is 1.2 m wide, so a narrower roll could take it, at double thickness. Ask each supplier to quote both ways.

How does roll diameter affect an ironer's output?

Short answer

A larger roll gives linen a longer path against the heated surface, so it can remove more moisture at a given speed. That lets it run faster for the same finish. Wetter linen, heavier fabric or a folded item need slower running.

Ask suppliers for

  • Output for your item mix at your moisture level
  • Roll width, diameter and number of cylinders
  • Heat-up time from cold

Watch out for

  • Output quoted for an unstated item or moisture
  • Comparing width without diameter
  • Speeds your feeding staff can't keep up with

Should a commercial ironer be electric, gas or steam heated?

Short answer

Electric needs only a suitable supply, often three-phase on larger machines. Gas needs a gas supply, flue or ventilation and the right installer. Steam suits sites that already have a steam supply.

For gas, "no person shall carry out any work in relation to a gas fitting or gas storage vessel unless he is competent to do so" (Gas Safety (Installation and Use) Regulations 1998, regulation 3). HSE says that in workplaces such as shops, restaurants, schools and hospitals this work must be done by a Gas Safe registered engineer qualified to do it, and in places such as factories and agricultural premises by a competent person (HSE). Employers must keep gas appliances, pipework and flues "maintained in a safe condition so as to prevent risk of injury to any person" (regulation 35).

Ready to compare quotes?Tell us about your laundry once and a specialist UK commercial laundry supplier will come back with options to buy, lease or rent.
Get quotes

How wet should linen be when it goes into an ironer?

Short answer

Damp, not wet and not bone dry. Too wet and the ironer must run slowly or linen comes out damp; too dry and creases are harder to remove. Follow the maker's guidance for your fabric.

What are the safety rules for a commercial ironer?

Short answer

The main hazards are the in-running nip, where linen is drawn between roll and bed and fingers can follow, and hot surfaces. PUWER requires effective guarding, burn protection and emergency stops where appropriate, and adequate training.

A jam tempts people to reach in. Stop the machine and follow the maker's procedure; never reach in.

Where should a commercial ironer go?

Short answer

Close to the dryers, with clear space at the feed and delivery sides, the right energy supply, and ventilation for the heat and vapour it gives off.

Heat and vapourAsk whether the model needs ducting to outside. HSE advises checking that all rooms with gas appliances have adequate ventilation (HSE).
FlowDamp linen in from the dryers, finished linen out to folding and clean storage.
Fire risk assessmentIn England and Wales the responsible person must make "a suitable and sufficient assessment of the risks" (Fire Safety Order article 9). Include hot rolls and lint.
AccessIroners are long: measure doors and corridors on the way in.

What should you ask a commercial ironer supplier?

Short answer

Send each supplier the same brief, then compare their recommended roll width and diameter, output for your mix, installation, guarding, training and servicing, all in writing.

  1. Same brief to eachItems and counts, widest item, hours, how you dry first, energy supply, room plan and door widths.
  2. Output on your mixItems per hour at your moisture level, and how many operators that assumes.
  3. Guarding and trainingHow the feed guard works and is tested, where the stops are, and training provided.
  4. Servicing and wear partsService intervals, padding and cover replacement, parts and response times.
  5. How to payBuy, lease or an all-in plan; see laundry equipment leasing.

Get quotes for a commercial ironer

Tell us about your laundry once. We pass it to a specialist UK commercial laundry equipment supplier, who will:

  • Talk through your laundry: what you wash, how much, the space you have, and your water, drainage, power and any gas.
  • Quote in writing to buy, lease or on a monthly plan, with delivery, installation and servicing shown.
  • Explain the service cover: response times, what's included, and who to call when a machine stops.

For businesses and organisations. Prefer email? Write to [email protected] with your business type, size and the machines you need.

Free quotes

Tell us about your laundry

Three quick steps. Free and no obligation.

Your laundry
Options
Your details

ICO registered ZA810991 No obligation For businesses

Commercial ironer: frequently asked questions

What is the difference between a rotary ironer and a flatwork ironer?

Both press linen against a heated surface. 'Rotary' usually means a compact, hand-fed roll ironer; 'flatwork' usually means a larger heated-cylinder machine, often with a feeder and folder. Compare roll width, diameter and heating rather than the name.

What size commercial ironer do I need?

Roll width comes from your widest item and whether you feed it folded. Speed comes from roll diameter, heat and moisture: ask suppliers to quote output for your item counts.

Can a commercial ironer take sheets straight from the washer?

It depends on how much water the washer spin leaves and the ironer's drying capacity. Some laundries part-dry linen first; ask suppliers what they recommend.

Can a commercial sheet ironer press shirts or towels?

No. Shirts and uniforms need garment finishing, and towels are tumble dried and folded because pressing flattens the pile.

Is a gas or electric ironer better?

It depends on your site. Gas needs a gas supply, flue or ventilation and a Gas Safe registered engineer or competent person, as HSE explains. Ask suppliers to compare running costs for your use.

What guarding does a commercial ironer need?

PUWER regulation 11 requires effective measures to prevent access to dangerous parts or stop them first, usually a finger guard at the feed. Guards must be maintained and not easily bypassed.

Do staff need training to use an ironer?

Yes. PUWER regulation 9 requires adequate health and safety training for everyone who uses work equipment, including its risks and precautions.

How often do ironer padding and covers need replacing?

It depends on use and what goes through; buttons, zips and grit wear them faster. Ask suppliers for the interval at your volume.

Sources

We checked the facts on this page against these sources on 19 November 2026. Guidance changes: check the current version before you rely on it.

  1. Provision and Use of Work Equipment Regulations 1998, regulation 11: dangerous parts of machinery (legislation.gov.uk)
  2. Provision and Use of Work Equipment Regulations 1998, regulation 13: high or very low temperature (legislation.gov.uk)
  3. Provision and Use of Work Equipment Regulations 1998, regulation 16: emergency stop controls (legislation.gov.uk)
  4. Provision and Use of Work Equipment Regulations 1998, regulation 9: training (legislation.gov.uk)
  5. Provision and Use of Work Equipment Regulations 1998, regulation 5: maintenance (legislation.gov.uk)
  6. Gas Safety (Installation and Use) Regulations 1998, regulation 3: qualification and supervision (legislation.gov.uk)
  7. Gas Safety (Installation and Use) Regulations 1998, regulation 35: duties of employers (legislation.gov.uk)
  8. Gas safety for employers (HSE)
  9. Regulatory Reform (Fire Safety) Order 2005, article 9: risk assessment (legislation.gov.uk)